Find the washing and curing guidance for your exact resin. Browse by maker or resin type, then open the manufacturer’s full instructions before using a setting.
A label such as ABS-like or tough does not establish the same process. The washing liquid must also suit your equipment. These are summaries of manufacturer documents, not product tests or a compatibility guarantee. Where documents disagree or we could not verify a setting, the record says so.
The resin records
Product names and types describe the exact records below; they are not interchangeable settings. Not every library entry is supported by the wash and cure time tool.
No matching resins. Clear the filters or try a maker, product name or washing liquid.
Anycubic / Standard
Standard Resin V2
An alcohol-washed resin with conflicting maker timing instructions. Confirm the process for your bottle before selecting a cycle.
Wash medium: IPA at least 95%; check the maker before using another cleaner
Washing, drying & curing instructions
- Wash · Wash-and-cure station
- The linked TDS states at least 3 minutes; the product-page instructions state about 10 minutes in an Anycubic Wash & Cure. These are different instructions, not a recommended range. Ask Anycubic which applies to your bottle and equipment.
- Dry
- The product page includes drying before secondary curing. Follow the resin and equipment instructions; no universal drying duration is established here.
- Cure
- The TDS states 3 minutes; the product page states 3–5 minutes. Confirm the applicable schedule with Anycubic rather than averaging these figures.
- Cure equipment / context
- Maker's wash-and-cure process; confirm the exact curing unit
Scope and limits
- Standard Resin V2 only; not Standard V1, High Speed, ABS-like or a water-washable product.
- The sources do not establish a separate schedule for every colour, hollow part or curing unit.
Manufacturer sources
Siraya Tech / ABS-like
Regular Fast
The Regular Fast guide describes brush cleaning and short UV post-curing in air. Its washing time is not a station cycle.
Wash medium: 95% ethanol preferred, or IPA
Washing, drying & curing instructions
- Wash · Manual brush cleaning
- The guide specifies 4 minutes of cleaning with a soft hair-bristle brush to remove excess resin. Follow the full cleaning sequence and check the exact solvent product.
- Dry
- Remove all solvent. The guide requires a completely dry, non-sticky surface before UV post-curing; do not use bare skin to check the part.
- Cure
- The guide specifies 1–2 minutes, using UV in air. Water submergence is not required for Regular Fast.
- Cure equipment / context
- 395–405 nm UV; follow the complete maker guide
Scope and limits
- Regular Fast only; do not transfer this schedule to Fast Tough, Fast Mecha or other specialist variants.
- No separate large-part or hollow-part schedule is established here.
Manufacturer sources
Siraya Tech / Tough
Blu — original guide
The Blu guide gives an alcohol-immersion limit and a separate post-cure instruction. A maximum immersion time is not a washing target.
Wash medium: 95% ethanol preferred, or IPA
Washing, drying & curing instructions
- Wash · Brush cleaning with limited alcohol immersion
- Remove excess resin using a brush. Do not submerge parts in alcohol for more than 5 minutes. The guide suggests repeated cleaning and drying for complex cavities; it does not supply one fixed wash target.
- Dry
- Remove all resin residue and remaining alcohol. The guide requires the part to be dry before curing.
- Cure
- About 15 minutes is stated in the original guide. The maker discusses water-assisted curing separately; read the complete instructions before changing the process.
- Cure equipment / context
- 395–405 nm UV
Scope and limits
- Do not assume the original schedule covers Blu Easy, Blu Lava, Nylon, Mecha or every new formulation and colour.
- This summary is not the maker's separate biocompatibility or autoclaving protocol.
Manufacturer sources
Siraya Tech / Flexible
Tenacious — Clear and Obsidian Black
Tenacious instructions vary with part geometry. The guide distinguishes thin, small parts from larger, thicker or more complex parts.
Wash medium: 95% ethanol preferred, or IPA
Washing, drying & curing instructions
- Wash · Manual brush cleaning
- The guide specifies 2–3 minutes of cleaning action with a brush. Complex cavities may need repeated cleaning and drying; this is not a station cycle.
- Dry
- Remove the remaining alcohol before post-curing. Confirm that resin residue has been cleaned off; do not touch the part with bare skin to assess it.
- Cure
- Approximately 10 minutes for thin, small models; longer for larger, complex or thick parts, up to 25 minutes. These descriptions do not establish a precise schedule for your geometry.
- Cure equipment / context
- 395–405 nm UV; the guide separately discusses water-assisted curing
Scope and limits
- This profile covers the regular Clear/Obsidian Black context, not a verified schedule for Tenacious Flex Black, Easy, Lava or mixtures.
- No fixed millimetre size cutoff or assurance of internal hollow-part curing is supplied.
Manufacturer sources
Anycubic / Water-washable
Water-Wash Resin 2.0
A water-washable formulation whose contaminated rinse water must stay out of drains. Official documents differ on the water-washing duration.
Wash medium: Water; the TDS also lists ethanol and IPA
Washing, drying & curing instructions
- Wash · Use the method approved for your exact bottle and washing equipment
- The TDS gives water washing of at least 3 minutes. The linked regional product table instead gives at least 5 minutes for water. Confirm the applicable instruction with Anycubic; do not turn the disagreement into a 3–5 minute recommendation.
- Dry
- The TDS says to dry models thoroughly inside and out and cure promptly. Do not leave uncured parts soaking for a prolonged period.
- Cure
- The TDS states 3 minutes in a wash-and-cure station. Confirm this against your bottle and equipment instructions.
- Cure equipment / context
- Maker's wash-and-cure station process; not a sunlight schedule
Scope and limits
- Water-Wash Resin 2.0 only; not Water-Wash Resin+, ABS-like water-washable resin or another version. The linked regional page mixes naming, so use the exact-product TDS and ask the maker to resolve the difference.
- Collect contaminated rinse water; follow the SDS and receiving waste service rather than assuming cured sediment permits drain disposal.
Manufacturer sources
ELEGOO / Standard
Standard Resin V2.0
ELEGOO identifies IPA and ethanol as cleaning options. A verified resin-specific wash duration and complete post-cure schedule are not supplied in this profile.
Wash medium: IPA or ethanol; confirm concentration with ELEGOO
Washing, drying & curing instructions
- Wash · Confirm the exact resin and equipment instructions
- The Standard V2.0 product page permits cleaning with isopropyl alcohol or ethanol. It does not establish a resin-specific wash duration in the checked text. Ask ELEGOO for the current instructions for your bottle.
- Dry
- No resin-specific drying duration was verified. Obtain the current resin and equipment drying instructions before post-curing.
- Cure
- No complete Standard V2.0 post-cure schedule was verified. Consult ELEGOO; do not substitute a printer layer-exposure figure or another resin's cure time.
- Cure equipment / context
- Confirm the curing equipment and schedule with ELEGOO
Scope and limits
- V2.0 only; not V1, Rapid Standard, 8K Standard or a water-washable formulation.
- Product-page colours include Grey, White, Black, Medium Slate Blue, Slate Blue and Orchid; no colour-specific post-processing schedule was established here.
- Low-odour marketing is not evidence that ventilation or protective equipment can be omitted.
Manufacturer sources
Prusament / Model
Resin Model+ Rich Black
The reformulated Model+ range has its own cleaning and curing instructions. Keep it separate from the earlier Model and Tough resin documents.
Wash medium: Prusament Resin Cleaner DPM or IPA
Washing, drying & curing instructions
- Wash · Use the current cleaner and equipment instructions
- The Model+ material page recommends 5 minutes when washing with DPM. The checked page does not assign that duration to IPA; obtain the IPA-specific process before using it.
- Dry
- No Model+ Rich Black drying duration was verified. Follow the current cleaner and equipment instructions; an older Model resin drying schedule is not automatically applicable.
- Cure
- The current Model+ page and Rich Black listing state 5 minutes or more in the CW1S. Confirm the complete process for your part and bottle.
- Cure equipment / context
- Original Prusa CW1S; the figure is not a schedule for any UV lamp
Scope and limits
- Model+ Rich Black only; the linked SDS is for Rich Black, not every colour.
- Do not transfer the earlier Model or Tough resin timing to Model+ or treat this as a biocompatibility process.
Manufacturer sources
Before you use a library record
Read the complete wash, dry and cure workflow and arrange a waste route. Water-washable describes a cleaning method; contaminated rinse water still needs collecting. Do not infer a hollow-part, skin-contact, dental or other specialist process from a general-purpose entry.
Missing a resin or found changed instructions? Send the exact product name and an official source. We add records after checking the documents; we do not fill missing settings with another resin’s figures.